Iowa DOT CDL General Knowledge Practice Test 4
Test 4 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Iowa test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.
-
2. Why should water never be used on an electrical fire or a gasoline fire?
Show answer
Answer C: It spreads the fuel and conducts the current
Water carries current back to the person holding the hose and floats burning fuel outward, which is why a B:C rated extinguisher is carried instead.
-
3. How do you test for leaks in a hydraulic brake system during the pre-trip inspection?
Show answer
Answer A: Pump the pedal three times, then hold firm pressure for five seconds and make sure the pedal does not move
If the pedal sinks while you hold pressure, fluid is escaping or air is in the lines, and the vehicle must not be driven until the problem is repaired.
-
4. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?
Show answer
Answer B: Any bus carrying passengers
The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.
-
5. A car that passed you on the right slows and stays alongside your trailer. What is the best response?
Show answer
Answer D: Ease off the accelerator so the car can move clear
A vehicle sitting beside a trailer is in a blind area and has nowhere to go if you need the lane, so the safest fix is to let it get ahead or behind.
-
6. Part of your load stands high enough to hide a rear lamp or a reflector. What must be done?
Show answer
Answer B: The load must be moved or extra lamps fitted so the required lights can be seen
Required lamps and reflectors must remain visible; if the cargo blocks them, the load is rearranged or additional lamps are fitted so the vehicle can still be seen.
-
7. How does Iowa classify operating a commercial motor vehicle while disqualified, when a commercial license is required for that vehicle?
Show answer
Answer D: As a serious misdemeanor
Iowa Code section 321.218 makes operating a commercial motor vehicle while disqualified a serious misdemeanor when a commercial driver's license or commercial learner's permit is required for that vehicle.
-
8. You are asked to drive a truck loaded with enough hazardous materials to require placards. What must you have?
Show answer
Answer C: A hazardous materials endorsement on your commercial driver license
Driving a vehicle that must be placarded requires the H endorsement, which involves a separate knowledge test and a security background check.
-
9. Your truck has a backup alarm that sounds whenever reverse is selected. What may a driver rely on it for?
Show answer
Answer D: Very little; it warns some people but cannot show you what is behind the vehicle
An alarm may not be heard over yard noise or by someone wearing hearing protection, so it never replaces looking at the path yourself.
-
10. On a set of dual tires, which condition must be reported as a defect?
Show answer
Answer D: The two tires are touching each other or rubbing on part of the vehicle
Duals that touch each other or the vehicle overheat and wear quickly, so they must be separated by proper spacing and inflation before driving.
-
11. How are the extra gears of a multi-speed rear axle or auxiliary transmission usually controlled?
Show answer
Answer D: With a selector knob or switch on the gearshift lever of the main transmission
A range selector on the shift lever lets the driver choose the extra gear range while shifting the main transmission.
-
12. What must the driver confirm about the required emergency equipment before a trip?
Show answer
Answer A: That it is in place, in working order and ready to be used
Federal rules require the driver to be satisfied that the emergency equipment is present and ready, because it is needed at the worst possible moment.
-
13. A load overhangs the rear of the trailer. What must the driver check before leaving?
Show answer
Answer D: That the overhang is marked as required, with flags or lamps as conditions demand
A projecting load has to be made visible to other drivers, with flags in daylight and lamps when lights are required, so nobody runs into what they cannot see.
-
14. What is checked about the engine cooling system during the engine compartment inspection?
Show answer
Answer C: That the coolant level is adequate and the radiator and hoses are not leaking
A low coolant level or a leaking hose leads to overheating, which can stop the vehicle in a place where stopping is dangerous.
-
15. You miss a gear while double clutching and the transmission is stuck in neutral. What should you do?
Show answer
Answer B: Return to neutral, release the clutch, bring engine speed to match road speed and try again
Forcing the lever damages the gears; matching the engine speed to the road speed lets the gear engage cleanly on the next try.
-
16. Which wheel or rim condition must be treated as a defect during the walkaround?
Show answer
Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts
Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.
-
17. Which lights should be used in fog, by day or by night?
Show answer
Answer A: Low beams and fog lights, together with the four-way flashers
High beam light bounces back off the water droplets and makes seeing worse, while low beams, fog lights and flashers help you see and help others see you.
-
18. Dry bulk tanks call for extra caution mainly because of what?
Show answer
Answer C: A high center of gravity combined with a load that can shift
Dry bulk loads ride high and can move inside the tank, which makes the vehicle easier to tip in a curve.
-
19. Which vehicle is most likely to be pushed around by a strong crosswind?
Show answer
Answer B: An empty van trailer
A large flat side with very little weight behind it gives the wind the most surface and the least resistance, which is the empty van trailer.
-
20. An unblocked crate 4 feet long and weighing 900 pounds needs at least how many tiedowns?
Show answer
Answer D: One
An article 5 feet or less in length and 1,100 pounds or less in weight is covered by a minimum of one tiedown.
-
21. What are you looking for when you check the hubs and wheel seals during the walkaround?
Show answer
Answer B: Leaking oil or grease, which can also contaminate the brake linings
A leaking hub seal starves the bearing of lubricant and the escaping oil or grease can soak the brake linings and cut braking power.
-
22. A driver hauling a sealed trailer that cannot be opened is still responsible for what?
Show answer
Answer D: Making sure the rig is not over the gross or axle weight limits
A seal prevents inspecting the contents, but the driver must still confirm the vehicle is not overloaded.
-
23. A vehicle becomes unsafe while you are already on the road. What does the federal rule allow?
Show answer
Answer A: Continuing only to the nearest place where repairs can safely be made
If stopping where you are would be more dangerous than moving, the rule allows you to reach the nearest place where the vehicle can safely be repaired, and no further.
-
24. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
25. During the walkaround you find the reflective conspicuity tape along the trailer caked with road grime. What should you do?
Show answer
Answer B: Clean it, because dirty reflective material cannot make the trailer visible at night
Reflective sheeting only works if light can reach it and bounce back, so a dirty strip leaves the trailer effectively unmarked to approaching traffic.
-
26. During a trip you stop for a break. Which items should you check before driving on?
Show answer
Answer B: Tires, wheels and rims, brakes, lights, reflectors, electrical connections and cargo securement
Critical items can change during a trip, so each stop is used to recheck the tires, wheels, brakes, lights, connections and cargo.
-
27. In the seven-step method, what comes immediately after starting the engine and inspecting inside the cab?
Show answer
Answer D: Turn off the engine and check the lights
Step four shuts the engine down and switches on the lamps needed for driving so the driver can leave the cab and confirm they actually work.
-
28. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?
Show answer
Answer D: The seat cushion upholstery
The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.
-
29. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
30. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?
Show answer
Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel
Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.
-
31. In dense city traffic you cannot see 12 seconds ahead because other vehicles block the view. What is the best response?
Show answer
Answer A: Slow down and open up more space in front of you
When you cannot see far enough ahead, extra following distance buys back the reaction time that the blocked view has taken away.
-
32. You must steer hard around an obstacle at highway speed. What is the correct technique?
Show answer
Answer B: Avoid braking while turning, turn only as far as needed, and countersteer as soon as the obstacle is passed
Braking during a hard steering input can lock the wheels and start a skid, and turning back at once keeps the vehicle from running off the far side of the road.
-
33. What happens to braking performance if oil or grease reaches a brake lining?
Show answer
Answer B: That brake loses much of its effect and the vehicle can pull to one side
A contaminated lining cannot grip the drum, so that wheel contributes little braking and the vehicle pulls toward the side that is still working.
-
34. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
35. What does the gross combination weight rating cover?
Show answer
Answer B: The maximum loaded weight of the power unit together with the trailer or trailers it tows
The combination rating takes in the power unit and everything behind it, loaded, as specified by the manufacturer.
-
36. How many questions are on the general knowledge test for any Iowa CDL class, and how many may be missed?
Show answer
Answer B: 50 questions, 10 may be missed
The Iowa DOT CDL Testing page lists the general knowledge test for any CDL as 50 questions with 10 allowed misses.
-
37. The scale shows that your combination is over the legal gross weight. Why will sliding the tandems not fix it?
Show answer
Answer B: Because sliding the axles changes where the weight sits, not how much there is
Repositioning axles redistributes weight between axle groups; when the total is too high, freight has to come off the vehicle.
-
38. What should the ammeter or voltmeter show once the engine is running?
Show answer
Answer D: A reading in the normal charging range
With the engine running, the alternator should be charging; a discharge reading or an abnormal charge level means an electrical fault.
-
39. Below 40 mph, what following distance does the standard commercial rule of thumb call for?
Show answer
Answer C: One second for every 10 feet of vehicle length
The base rule allows one second of space for each 10 feet of vehicle length while speed stays under 40 mph.
-
40. Where do you find the maximum weight a tire can safely carry?
Show answer
Answer D: Stamped on the sidewall of the tire itself
Each tire is marked with the greatest weight it can carry at a stated inflation pressure, and the load on an axle must stay within the total for its tires.
-
41. As a long vehicle goes around a corner, how do the rear wheels travel compared with the front wheels?
Show answer
Answer A: They follow a tighter path, closer to the inside of the turn
The rear wheels off-track toward the inside of the turn, and the longer the vehicle the bigger the difference, which is why the front must swing wide enough to keep the rear off the curb.
-
42. A strap is a little too long, so a driver ties a knot in it to take up the slack. Is that acceptable?
Show answer
Answer C: No, tiedowns must not contain knots
A knot destroys the rated strength of a tiedown, so the rules do not allow knotted securement devices; the excess is taken up by the winch or ratchet instead.
-
43. What may the holder of an Iowa commercial learner's permit not do, even when properly accompanied?
Show answer
Answer D: Operate a vehicle transporting hazardous materials
Iowa Code section 321.180 states that a commercial learner's permit is not valid for the operation of a vehicle transporting hazardous materials as defined in the federal regulations.
-
44. You have just passed another vehicle on a two lane road. What tells you it is safe to return to your lane?
Show answer
Answer B: You can see the whole front of that vehicle in your right mirror
Seeing the entire front of the vehicle you passed in your mirror proves you are far enough ahead to move back over without cutting the driver off.
-
45. After starting a trip, when must a driver first re-inspect the cargo and the devices holding it?
Show answer
Answer A: Within the first 50 miles
Federal rules require a check of the load and its securement within the first 50 miles, because settling and vibration loosen straps and chains early in a trip.
-
46. When is tire pressure most accurately compared with the recommended figure?
Show answer
Answer B: When the tires are cold, before the vehicle has been driven
Recommended pressures are cold pressures, so a reading taken before the tires have heated up is the only one that can be compared directly.
-
47. What should you do with the previous driver vehicle inspection report before starting your trip?
Show answer
Answer B: Review it and confirm that listed defects were certified as repaired or as not needing repair
Reviewing the last report and the carrier certification tells you whether reported defects have been corrected before you take the vehicle out.
-
48. What is the correct order for a basic double clutch upshift?
Show answer
Answer B: Release the accelerator and push the clutch, shift to neutral, release the clutch, let engine speed drop, push the clutch again and shift to the higher gear
Double clutching passes through neutral with the clutch released so engine speed can drop to match the next gear before it is engaged.
-
49. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
50. You are inspecting the vehicle alone and need to confirm that the stop lights work. Which method is correct?
Show answer
Answer A: Have a helper press the brake pedal, or apply the brake in a way that keeps it on while you check from outside
Stop lights are checked from outside the vehicle while the brakes are applied, so a helper or a brake held on is needed.